News
-
Development Trend of Pneumatic Component
The development trend of pneumatic components can be summarized as: High quality: the life of the solenoid valve can reach 100 million times, and the life of the Pneumatic cylinder (The Pneumatic cylinder is composed of a Pneumatic Aluminum Tube, Pneumatic Cylinder Kits, a piston, a Hard Chrome P...Read more -
Pneumatic Cylinder Composition
The Pneumatic cylinder is composed of a Pneumatic Aluminum Tube, Pneumatic Cylinder Kits, a piston, a Hard Chrome Piston Rod and a seal. Its internal structure is shown in the “SMC Pneumatic Cylinder Schematic”: 1)Pneumatic Aluminum Tube The inner diameter of the Air Cylinders Tube re...Read more -
Characteristics of stainless steel piston rod
Stainless steel piston rods are mainly used in hydro/pneumatic, construction machinery and automobile manufacturing. Piston rods are rolled because residual compressive stress remains in the surface layer, helping to close microscopic cracks on the surface and hindering the expansion of erosion. ...Read more -
piston rod machined material
1. 45# steel Under normal circumstances, if the load of the piston rod is not very large, 45# steel is generally used for production. Since 45# steel is a commonly used medium carbon quenched and tempered structural steel, it has high strength and good machinability, especially when the welded ro...Read more -
304 316 Stainless steel cylinder tubes have excellent performance characteristics
The inner diameter of the stainless steel cylinder tube indicates the output force of the cylinder(made by 304 or 316stainless steel cylinder tubes). The piston should slide smoothly in the cylinder, and the inner surface roughness of the cylinder should reach ra0.8um. The inner surface of the st...Read more -
The service life of 304 stainless steel
304 stainless steel pipe(use in pneumatic cylinder) has a long service life. Judging from the use of foreign stainless steel pipes, the service life of 304 stainless steel pipes can reach 100 years in most cases, and 70 years in less cases, which is almost the same as that of buildings. Of course...Read more -
Principle and Design of Pneumatic System
1. Pneumatic FRL parts Pneumatic FRL parts refers to the assembly of three air source processing elements, air filter, pressure reducing valve and lubricator in pneumatic technology, called pneumatic FRL parts, which is used to purify, filter and reduce the air source entering the pneumatic instr...Read more -
How to disassemble the sc standard cylinder correctly？
The system where the sc standard pneumatic cylinder (Made by Aluminium Pneumatic Cylinder Tube) is located requires after-sales maintenance and maintenance in order to run more lastingly. Maintenance includes dismantling and cleaning some pneumatic components, replacing old parts, etc. Autoair wi...Read more -
Basic requirements and roll forming of piston rod
After the piston rod is formed by rolling, its rolling surface will form a layer of cold work hardening, which can reduce the elastic and plastic deformation of the grinding pair contacting the surface, and then improve the wear resistance of the cylinder rod surface, and at the same time avoid t...Read more -
Stainless steel piston rod
1.Cleaning process of stainless steel piston rod(use in pneumatic cylinder) In order to be able to better complete the operation of the stainless steel piston rod, then we should clean it, which is also for us to have a better quality stainless steel piston rod. To put it simply, we can use soap ...Read more -
This refillable toothpaste container is designed to reduce the waste generated by traditional toothpaste tubes!
Mimo is a revolutionary refillable toothpaste tube that pumps toothpaste into each tube from the bottom with the help of an external refill basin. We didn’t realize how many waste toothpaste tubes would actually be produced.We brushed our teeth twice a day, crossing our fingers, and brushed...Read more -
Profiles For Pneumatic Cylinders
Keeping the assembly process simple is always a smart way to make any product.One of the easiest ways to achieve linear or rotary motion during assembly is to use pneumatic actuators. Carey Webster, Engineering Solutions Manager of PHD Inc., pointed out: “Compared with electric and hydraulic actu...Read more
